Bosch Dishwasher E24 and E25 Error Code Repair in Indio: Drain Pump, Cover, and Check Valve Replacement

Standing gray water. Two flashing codes. I drove out to a house near Highway 111 and Monroe Street in Indio (92201) this afternoon because the owner's Bosch 800 Series dishwasher (model SHPM78Z55N) quit mid-cycle with a full tub of soapy dishwater and alternated between error codes E24 and E25 on the top display; she tried canceling the wash twice and scooped half the sump out with a coffee mug, yet the drain pump still refused to push a single drop toward the sink disposal, which almost always points straight to a failed pump stator, a popped impeller cover, or a torn check valve down in the sump pit. Time to open it up.
Checking Error Codes E24 and E25 With a Multimeter
External drains come first. Before touching a screwdriver inside a Bosch dishwasher, I always pull the corrugated drain hose off the under-sink air gap and blow air through the disposal inlet to rule out a kitchen grease plug; once that external line tested wide open, I switched off the dedicated 120V breaker, closed the brass hot water supply valve under the sink, pulled the stainless mesh filter cylinder out of the bottom tub, and grabbed my Fluke multimeter and 1/4-inch nut driver to inspect the lower drain components. Three bad parts showed up fast.
- Power and Water Shutoff: First I unplugged the 120V power cord inside the sink cabinet, flipped the circuit breaker off, and turned the hot water supply valve completely shut before backing out the lower toe-kick screws with my 1/4-inch nut driver and T20 Torx bit.

- Broken Internal Pump Cover (Part #00611322): Right away I saw why code E25 fired first; the white plastic internal pump cover that snaps over the impeller blades had sheared its rear retaining tab and floated crooked out of the sump slot, and without that cover locked tight over the rotor, a Bosch drain pump can't build enough suction pressure to lift water up the drain hose.
- Broken Non-Return Check Valve (Part #00611320): Next I pulled the black rubber non-return check valve out of the sump discharge channel, where the flexible flapper hinge had split clean in half and curled backward so dirty sink water siphoned straight back into the tub and tripped the E24 fault.
- Failed Drain Pump Stator (Part #00631200): Finally I popped the lower splash guard off and touched my multimeter probes across the three pins on the 3-phase BLDC drain pump and the cabinet thermal fuse; while the thermal fuse read a healthy 0.1 Ohms, two of the pump stator windings flashed OL (open loop) instead of the factory 85 Ohms balance because the overheated motor coils had burned open completely.

Replacing the Bosch Drain Pump, Pump Cover, and Check Valve
Fix all three together. Putting a brand-new drain pump into a Bosch sump while leaving a broken impeller cover or a torn check valve in place will trigger an E24 or E25 callback within two days; once the Indio homeowner approved our $490.00 flat-rate repair estimate, I walked out to the service van and pulled a genuine OEM Bosch Drain Pump (Part #00631200), a new OEM Internal Pump Cover (Part #00611322), and a new OEM Non-Return Check Valve (Part #00611320) so we could rebuild the entire drain path properly in one trip.
- Step 1 - Wet-Vac Sump Cleanout: With power and hot water still disconnected, I used my service wet-vac to pull every ounce of dirty dishwater, lime grit, and broken plastic clip pieces out of the sump bowl.
- Step 2 - Bench Testing and Swapping the Drain Pump: Before locking the new part in, I checked the new OEM #00631200 drain pump right out of the box with my multimeter and got a dead-even 85.2 Ohms across all three pin pairs; then I twisted the burned-out pump free from the front toe-kick bay, greased the new rubber O-ring, and rotated the new pump home until the lock tab clicked.

- Step 3 - Installing the New Non-Return Check Valve: Down inside the sump discharge port, I pulled out the torn rubber piece and pressed the new OEM #00611320 check valve squarely into the guide groove so dirty sink water stays locked out of the tub.
- Step 4 - Locking Down the New Internal Pump Cover: I lined the new OEM #00611322 pump cover up over the impeller pocket and pressed the back tab down firmly until it snapped dead-flat against the sump floor, then reinstalled the stainless mesh filter and toe-kick guard with my 1/4-inch nut driver.
| Diagnostic Test Point | Reading Before Repair | Result After OEM Service | Factory Spec |
|---|---|---|---|
| Control Panel Error Codes | Active E24 and E25 drain faults | Cleared completely; full cycle active | Zero stored faults. |
| Drain Pump Stator (#00631200) | OL (Open windings; dead pump) | 85.2 Ohms balanced across 3 phases | 80 to 90 Ohms balanced. |
| Internal Pump Cover (#00611322) | Broken rear clip; popped out of sump | New OEM cover locked flush over rotor | Sealed tight. |
| Non-Return Check Valve (#00611320) | Split rubber flapper; active backflow | New OEM check valve; zero backflow | One-way seal intact. |
| Thermal Fuse & Evacuation Time | 0.1 Ohms fuse; 0 GPM drain rate | 0.1 Ohms fuse; tub emptied in 28 sec | Under 45 seconds. |
Every single drain metric returned to factory numbers. Before we replaced the burned-out #00631200 pump, snapped #00611322 cover, and torn #00611320 check valve, water couldn't clear the sump cavity at all; right after reassembly, the tub evacuated cleanly with zero sink siphon backflow.
Final Drain Cycle Verification and Leak Check
Strong flow right away. I turned the under-sink hot water valve back on, plugged the 120V power cord into the cabinet outlet, poured two full pitchers of water into the stainless tub, and held down the Start button to force a cancel-and-drain sequence; the new Bosch 3-phase drain pump hummed softly with zero rattling, pushed a strong column of water straight through the countertop air gap in 28 seconds flat, wiped both the E24 and E25 error codes off the display, and left my dry paper towel bone dry under the lower sump and drain hose clamps. No leaks anywhere. The Indio homeowner had her kitchen back in under an hour without shopping for a $1,200 replacement dishwasher.
If your Bosch dishwasher won't drain water, flashes E24 or E25 error codes, or backs dirty water into the bottom tub in Indio, La Quinta, Palm Desert, or anywhere in the Coachella Valley, book our professional dishwasher repair service online or call our local dispatch team at (760) 537-6751.
Transparent Invoice Breakdown
ETS Appliance Repair provides upfront, flat-rate pricing with zero hidden fees before work begins:
| Service Item / Component | Description | Investment |
|---|---|---|
| Technician Diagnostic, Air Gap Check & Multimeter Stator Test | Air gap inspection, pump winding balance check & leak origin tracing (waived upon repair approval) | $0.00 |
| Genuine OEM Bosch 3-Phase Drain Pump Assembly | Factory-certified BLDC drain pump (Part #00631200) | $155.00 |
| Genuine OEM Bosch Pump Cover & Non-Return Check Valve | Impeller shroud (Part #00611322) & rubber check valve flapper (Part #00611320) | $85.00 |
| Certified Repair Labor | Sump wet-vac cleanout, toe-kick teardown, pump/cover/valve installation & leak test | $250.00 |
| Total Repair Investment | Complete Drain System Rebuild & 90-Day Parts and Labor Warranty | $490.00 |
Repair completed on-site in Indio, CA (92201) in approximately 60 minutes. Backed by our standard 90-day parts and labor warranty under CA BHGS License #A51622.
Need Technician Assistance Today?
$99.95 Technician Diagnostic Visit • 100% Waived With Completed Repair.
More Articles & Troubleshooting Guides

Samsung Microwave Touchpad Not Working in Cathedral City: $475 Door Assembly Diagnosis
A Samsung over-the-range microwave in Cathedral City flashed a -SE- code with a dead touchpad. We verified 5V DC from the main board and traced the fault to a steam-corroded bonded door ribbon ($475 OEM part), saving the owner from an uneconomical $590 repair.

GE Monogram Refrigerator Stuck at 50°F in La Quinta: Sealed System Freon Leak Repair and Filter-Drier Replacement
A 42-inch built-in GE Monogram refrigerator in La Quinta was stuck at 50°F from a pinhole Freon leak on the filter-drier. We silver-brazed a new OEM drier, pulled a 450-micron deep vacuum, and recharged 5.5 oz of R-134a to restore 37°F cooling.
Real Google Reviews From Satisfied Clients
Verified customer ratings from homeowners and businesses across San Diego County & Coachella Valley.
Google Rating (28 Verified Reviews)
W K
“Henry has been great....couldn't have been more knowledgeable and did a great job.....hope if I need help again he is available”
Brent Lagace
“Great service! Excellent staff! Thank you!”
Chris Rea
“Henry arrived and quickly got the dryer opened up and vacuumed, checked all sensors and greased rollers. Very fast, very thorough! Great job!”
