HomeBlogFisher & Paykel Dishwasher Not Draining in Carmel Valley, San Diego: Drain Pump Replacement
Back to Blog
MaintenanceNov 10, 2026•5 min read•96 views

Fisher & Paykel Dishwasher Not Draining in Carmel Valley, San Diego: Drain Pump Replacement

DR
Daniel RodriguezMaster Dishwasher & Luxury Built-In Specialist
Verified San Diego Master Tech
Fisher & Paykel Dishwasher Not Draining in Carmel Valley, San Diego: Drain Pump Replacement

We caught a late-morning call near Del Mar Heights Road in Carmel Valley, San Diego (92130) for a Fisher & Paykel Double DishDrawer dishwasher (model DD24DAX9). The top drawer wouldn't drain a drop of water. Three inches deep. When the homeowner opened the drawer after a normal wash cycle, greasy dishwater sat pooled above the stainless steel filter plate and the control panel was beeping with fault code F2.

Checking the F2 Fault Code and Testing the Drain Pump With a Multimeter

I carried my wet-vac and tool bag into the kitchen to clear the standing water out of the top tub first. Once the sump bowl was dry, I popped out the oval kidney filter basket and lifted the stainless steel filter plate to check for glass shards, pistachio shells, or lemon seeds. The sump pit was spotless.

Next, I checked the external drain path under the kitchen sink. I disconnected the corrugated drain hose from the countertop air gap fitting and blew compressed air through the line toward the garbage disposal inlet. Wide open. No grease plug in the hose.

Unlike a standard Whirlpool or LG dishwasher that bolts a single circulation and drain pump underneath a tall tub, a Fisher & Paykel DishDrawer uses a compact, bayonet-mounted DC drain pump and motor rotor tucked directly into the drawer base.

  • Power and Water Isolation: I unplugged the 120V AC power cord inside the adjacent sink cabinet and turned the brass hot water supply valve clockwise until it stopped.
  • Impeller and Rotor Inspection: I twisted the locking ring inside the sump bowl and lifted the white plastic pump cover. When I tried spinning the drain pump impeller blades with my finger, the rotor felt notched and stiff. Overheated plastic smelled sharp right around the motor shaft seal.
Interior view of stainless steel DishDrawer tub with filter removed exposing drain sump
Interior view of stainless steel DishDrawer tub with filter removed exposing drain sump
  • Multimeter Resistance Check: I slid the top drawer out on its side rails, unclipped the lower wire connector plug, and touched my Fluke multimeter probes to the pump stator pins. A good Fisher & Paykel drain pump winding reads right around 18.5 Ohms across each phase. My meter flashed OL (open loop) on the first pair of pins and 0.2 Ohms (dead short) on the second pair.
Technician inspecting seized Fisher  Paykel DishDrawer drain pump impeller and rotor
Technician inspecting seized Fisher Paykel DishDrawer drain pump impeller and rotor

Dead open circuit. When water creeps past a worn shaft seal into the pump housing, the stator windings short out and the impeller stops spinning.

Pro Tip
According to the official Fisher & Paykel factory service manual, "Fault code F2 triggers when the drain pump fails to empty the wash tub within the ninety-second drain window. Technicians must verify stator resistance with a multimeter and replace the drain pump assembly if an open winding is found."
Warning
Always unplug the 120V power cord and shut off the hot water supply valve under the sink before removing the filter plate or reaching into a dishwasher sump pit. Broken cocktail glass often hides in murky standing water, and live electrical terminals sit right beneath the drawer tub.

Swapping Out the Bad Fisher & Paykel Drain Pump Assembly

With the shorted stator confirmed on my multimeter, I went out to the service van and grabbed a factory OEM Fisher & Paykel Drain Pump Assembly (Part #524285P).

Genuine OEM Fisher  Paykel replacement drain pump assembly part 524285P
Genuine OEM Fisher Paykel replacement drain pump assembly part 524285P
  • Step 1 - Releasing the Drawer Slides and Lower Access Cover: With the power cord unplugged and the water line shut off, I popped the side drawer release clips, slid the upper tub assembly forward onto my padded support stand, and unclipped the bottom motor terminal cover.
  • Step 2 - Unlocking the Bayonet Drain Pump Housing: From inside the tub base, I rotated the twist-lock mounting collar counter-clockwise to release the seized drain pump and pulled the damaged unit straight out of the sump pocket.
  • Step 3 - Cleaning the Sump Seat and Check Valve Flapper: I wiped out the rubber sump cavity, inspected the rubber backflow check valve flapper so dirty sink water wouldn't siphon back into the drawer, and lubricated the new nitrile O-ring seal with food-grade silicone grease.
  • Step 4 - Locking In the New OEM Drain Pump: I dropped the new OEM Fisher & Paykel #524285P drain pump into the keyed sump slots, twisted the bayonet lock ring until it clicked home, and re-verified the new stator pins at 18.4 Ohms on my multimeter before snapping the wire plug and stainless filter plate back in place.
Pro Tip
Fisher & Paykel DishDrawers use a super-fine mesh kidney filter that catches coffee grounds and food grit before they hit the drain impeller, but hard San Diego tap water quickly coats that mesh in white calcium scale. As our senior San Diego dishwasher technicians tell homeowners, "Pull your oval kidney trap out once a month and scrub the mesh under hot water with white vinegar and an old toothbrush so your drain pump doesn't overheat fighting through a clogged screen."
Diagnostic Test PointReading Before RepairResult After OEM Service
DishDrawer Status & Error CodeTub full of standing water; flashing F2 codeFault cleared; full wash and drain cycle active.
Drain Pump Stator ResistanceOL (Open winding) & 0.2 Ohms shorted18.4 Ohms balanced across all new OEM windings.
Pump Impeller & Shaft SealSeized rotor; water intrusion inside motor capBrand-new OEM pump (#524285P) spinning smoothly.
Full Tub Drain Evacuation Time0 GPM (Complete drain failure)Emptied full tub through air gap in 32 seconds.

Running the Diagnostic Drain Test and Checking for Leaks

After sliding the top drawer back onto its steel glides and locking the side clips, I turned the under-sink hot water valve back on and plugged the 120V power cord into the outlet.

Fisher  Paykel DishDrawer control panel running active cycle after drain pump replacement
Fisher Paykel DishDrawer control panel running active cycle after drain pump replacement

I placed the Fisher & Paykel controller into factory diagnostic mode, filled the tub to normal operating level, and triggered the forced drain test. Right away, the new drain pump hummed quietly and pushed a solid stream of water through the countertop air gap into the disposal line. The entire drawer pumped dry in 32 seconds flat.

While the pump ran, I shone my work light underneath the drawer frame and ran a dry paper towel around the lower sump O-ring seal and hose clamps. Bone dry underneath. Zero drips. The homeowner was glad to have their kitchen back in action for dinner without waiting two weeks for a specialty manufacturer dispatch.

If your Fisher & Paykel dishwasher won't drain water, beeps with an F1 or F2 error code, or leaves standing water in the bottom of the drawer in Carmel Valley or anywhere in San Diego County, book our local dishwasher repair service online or call our dispatch office at (619) 332-2028.

Transparent Invoice Breakdown

ETS Appliance Repair provides upfront, flat-rate pricing before we turn a single screw:

Service Item / ComponentDescriptionInvestment
Technician Diagnostic & Stator TestWet-vac evacuation, air gap inspection & multimeter stator testing (waived upon repair approval)$0.00
Genuine OEM Fisher & Paykel Drain PumpFactory-certified bayonet DC drain pump assembly (Part #524285P)$275.00
Certified Mechanical LaborDrawer slide teardown, bayonet pump replacement, O-ring sealing & leak verification$215.00
Total Repair InvestmentComplete OEM Drain Restoration & 90-Day Parts & Labor Warranty$490.00

Repair completed on-site in Carmel Valley, San Diego, CA (92130) in approximately 60 minutes. Backed by our standard 90-day parts and labor warranty under CA BHGS License #A51622.

Related Service Areas & Specialized Repairs:
Same-Day San Diego Service

Need Technician Assistance Today?

$99.95 Technician Diagnostic Visit • 100% Waived With Completed Repair.

Call (619) 332-2028
Google Customer Reviews

Real Google Reviews From Satisfied Clients

Verified customer ratings from homeowners and businesses across San Diego County & Coachella Valley.

4.7

Google Rating (28 Verified Reviews)

WK

W K

a month ago

“Henry has been great....couldn't have been more knowledgeable and did a great job.....hope if I need help again he is available”

Coronado / San Diego, CA
Appliance Diagnostic & Repair
BL

Brent Lagace

a week ago

“Great service! Excellent staff! Thank you!”

San Diego / Coronado, CA
Appliance Diagnostic & Repair
CR

Chris Rea

a month ago

“Henry arrived and quickly got the dryer opened up and vacuumed, checked all sensors and greased rollers. Very fast, very thorough! Great job!”

San Diego / Coronado, CA
Dryer Repair & Service
Reviews automatically synchronized via official Google Places API
Have you used our service? Leave a review on Google →
Call Now