GE French Door Refrigerator Warm at 67°F: Evaporator Fan Replacement & Steam Defrost in Encinitas

I went out to a house in Encinitas to look at a GE French door refrigerator. The customer noticed that the top section was warm and the milk was spoiling. I pulled out my thermometer and checked the middle shelf. It was 67 degrees inside the fridge, but the freezer down below was still making ice.
Checking the Airflow and Diagnosing the Fan Failure

I put my hand over the air vents at the back of the top cabinet and felt no cold air coming through. The compressor at the bottom of the fridge was running, so I knew the cooling system was working. In these refrigerators, cold air is made in the freezer and blown up into the fridge by a small evaporator fan. If that fan stops, the fresh food section will warm up to room temperature.

I took the freezer drawers out and removed the back plastic panel to inspect the evaporator coils. The coils were packed with frost because the fan had stopped. I unplugged the fan motor connector and tested it with my multimeter. The control board was sending 12 volts DC to the fan, but the motor was dead and would not turn.
Steaming the Coils and Installing the OEM Fan

The coils had a lot of frost on the fins, so I hooked up my steam machine. I melted all the ice off the aluminum tubing and made sure the drain trough cleared out.

Then I popped the bad fan out of the housing and put in a new OEM GE evaporator fan motor. I plugged the wire harness in and turned the power on. The new fan started spinning right away and pushed cold air up into the top compartment.
I put the back cover and the freezer drawers back together. After about 45 minutes, the thermometer showed the temperature dropping down toward 38 degrees.
If your refrigerator is not circulating air or food is spoiling on the top shelves, schedule our refrigerator repair services in San Diego or call ETS Appliance Repair directly at (619) 332-2028 for fast local service.
Transparent Invoice Breakdown
Here is the exact cost breakdown for this repair in Encinitas:
- Diagnostic Evaluation & Airflow Inspection: $99.95 (Waived with repair)
- Freezer Teardown, Steam Defrost & Coil Cleaning Labor: $195.00
- OEM GE Evaporator Blower Fan Motor Assembly: $170.00
- Drain Line Flush & System Airflow Verification: $100.00
- Total Final Cost: $465.00
Job completed on-site in Encinitas in about an hour. Parts and labor covered by warranty.
Need Technician Assistance Today?
$99.95 Technician Diagnostic Visit • 100% Waived With Completed Repair.
More Articles & Troubleshooting Guides

Bosch Dishwasher E24 and E25 Error Code Repair in Indio: Drain Pump, Cover, and Check Valve Replacement
A Bosch 800 Series dishwasher in Indio quit mid-cycle with a full tub of water and error codes E24/E25. We replaced a burned-out 3-phase drain pump, snapped impeller cover, and torn check valve to restore full 28-second drainage

Samsung Microwave Touchpad Not Working in Cathedral City: $475 Door Assembly Diagnosis
A Samsung over-the-range microwave in Cathedral City flashed a -SE- code with a dead touchpad. We verified 5V DC from the main board and traced the fault to a steam-corroded bonded door ribbon ($475 OEM part), saving the owner from an uneconomical $590 repair.
Real Google Reviews From Satisfied Clients
Verified customer ratings from homeowners and businesses across San Diego County & Coachella Valley.
Google Rating (28 Verified Reviews)
W K
“Henry has been great....couldn't have been more knowledgeable and did a great job.....hope if I need help again he is available”
Brent Lagace
“Great service! Excellent staff! Thank you!”
Chris Rea
“Henry arrived and quickly got the dryer opened up and vacuumed, checked all sensors and greased rollers. Very fast, very thorough! Great job!”
