HomeBlog Leaking Thermador Refrigerator Ice Maker Repair in Palm Desert: OEM Ice Maker Assembly Replacement
Back to Blog
Case StudyNov 13, 2026•5 min read•36 views

Leaking Thermador Refrigerator Ice Maker Repair in Palm Desert: OEM Ice Maker Assembly Replacement

AM
Andrew MitchellLead Ice Maker & Luxury Refrigeration Specialist
Verified San Diego Master Tech
	Leaking Thermador Refrigerator Ice Maker Repair in Palm Desert: OEM Ice Maker Assembly Replacement

We took a morning call near El Paseo in Palm Desert (92260) for a 36-inch built-in Thermador Freedom Collection refrigerator (model T36BT925NS). Water was dripping out of the lower freezer drawer onto the stone kitchen floor. Inside the freezer box, a two-inch sheet of clear ice covered the bottom stainless slide rails. The homeowner tried turning the ice maker off at the touchpad, but water had already frozen the ice bin solid and triggered an E10 fault code on the upper display.

Checking the E10 Code and Testing the Ice Maker With a Multimeter

I carried my tool bag into the kitchen and opened the freezer drawer to trace the water trail. Long icicles hung straight down from the front lip of the upper-left ice maker module into the storage bin below.

Icicles and frozen water sheet leaking from Thermador ice maker into freezer drawer
Icicles and frozen water sheet leaking from Thermador ice maker into freezer drawer

When a built-in Thermador refrigerator leaks water from the ice maker zone, two suspects top the list: either a weeping water inlet valve is pushing water past the seal, or the ice maker assembly itself has cracked or jammed mid-harvest.

  • Power and Water Shutoff: Before pulling any covers, I flipped the dedicated 15-amp kitchen circuit breaker off and closed the 1/4-inch braided stainless water supply valve behind the lower kickplate grille.
  • Multimeter Check on the Water Inlet Valve and Thermal Fuse: I pulled the bottom toe-kick panel and clipped my Fluke multimeter leads onto the primary ice maker water solenoid terminals. Resistance measured right on factory spec at 185 Ohms, and the valve seat held static line pressure with zero dripping. Up inside the ice maker head, I checked the inline safety thermal fuse (Part #00615792). It showed a clean 0.1 Ohms of continuity.
  • Inspecting the Cracked Ice Maker Mold and Gear Switch: I unbolted the two mounting screws and dropped the Thermador ice maker assembly down for a bench inspection. Right away, I found the culprit. Hard Coachella Valley tap water had built up thick calcium crust along the aluminum mold tray, cracking the front silicone seam wide open. Worse yet, the internal hall-effect position sensor had failed inside the gear head. Because the tray stopped at a 15-degree tilt after ejecting cubes, every 7-second water fill poured straight out of the crooked, cracked mold and ran down onto the freezer floor.
Thermador ice maker assembly mounted in upper freezer compartment before removal
Thermador ice maker assembly mounted in upper freezer compartment before removal
Pro Tip
According to the official Thermador factory service manual, "Error code E10 indicates an ice maker tray position or harvest motor fault. If the ice mold fails to return to the level home position before the water fill cycle, technicians must replace the complete ice maker assembly."
Warning
Always shut off the 120V circuit breaker (or unplug the power cord) and close the cold water shutoff valve before clearing jammed ice or removing a built-in refrigerator ice maker. Never chip at frozen ice maker trays with a screwdriver or kitchen knife, because puncturing the nearby aluminum evaporator tubing will release refrigerant gas and ruin the cooling system.

Removing the Bad Unit and Installing the New Thermador Ice Maker

You can't patch a cracked, calcium-pitted ice mold or swap internal micro-gears on a sealed Thermador module. Once the homeowner approved the $730.00 flat-rate repair quote, I grabbed a factory OEM Thermador Ice Maker Assembly (Part #11036056) from our service truck.

  • Step 1 - Steaming Out the Ice Sheet and Fill Tube: With the power and water off, I used a low-pressure service steamer to melt the frozen waterfall off the drawer glides and cleared a small plug of ice out of the upper plastic water fill tube.
  • Step 2 - Unclipping the Multi-Pin Wire Plug: I pressed the locking tab on the rear molex connector and disconnected the multi-pin wire plug feeding the ice maker motor, mold heater, and thermistor sensor.
  • Step 3 - Mounting and Leveling the New OEM Ice Maker: I slid the brand-new OEM Thermador #11036056 ice maker onto the stainless side bracket, plugged the multi-pin wire connector firmly into the rear socket, and checked the mold tray with a pocket torpedo level so water would sit flat in all eight cube cavities.
  • Step 4 - Flushing the Water Filter Line: Before turning the ice maker back on, I purged a gallon of water through the internal water line to clear out any loose mineral scale.
Pro Tip
Palm Desert and surrounding Coachella Valley cities have mineral-heavy tap water that eats up built-in ice maker molds and water valves faster than coastal cities. As our senior Palm Desert refrigeration technicians tell homeowners, "Swap your Thermador UltraClarity water filter cartridge every six months on the dot, even if the filter light hasn't turned red yet, because mineral scale locks up ice maker ejector gears long before you taste chlorine in your drinking glass."
Diagnostic Check PointReading Before RepairResult After OEM Service
Freezer & Floor StatusActive water leak; ice sheet on rails; E10 fault codeBone dry; E10 code cleared from display.
Water Valve & Thermal Fuse185 Ohms solenoid / 0.1 Ohms thermal fuseVerified intact; zero weeping under line pressure.
Ice Maker Module (#11036056)Cracked mold seam; stuck at 15-degree tilt on fillBrand-new OEM Thermador ice maker leveled at 0°.
Test Harvest & Fill CycleOverflowing water straight into the ice binClean 7-second fill; zero spills or drips.

Running the Factory Self-Test Cycle and Checking for Leaks

I opened the lower water shutoff valve, flipped the 120V circuit breaker back on, and held down the On/Off and SuperFreeze buttons to clear the stored E10 fault code.

Next, I pressed the test switch underneath the new Thermador ice maker head to force an immediate harvest and water fill test cycle. The ejector arm swept through a full 360-degree rotation, the tray returned dead-flat to its home stop, and the water solenoid opened for exactly seven seconds. Every drop of water stayed inside the new mold cavities.

I ran a dry paper towel under the fill tube collar, around the ice maker frame, and across the lower water valve fittings. Bone dry. Within two hours, the freezer was back down to -2°F and ready to drop its first clean batch of pyramid ice cubes. The homeowner was thrilled to stop the floor leak and save their $10,000 built-in Thermador column without waiting weeks for a warranty contractor.

If your Thermador refrigerator is leaking water from the ice maker, flashing an E10 or E11 error code, or building up sheets of ice in the freezer in Palm Desert or anywhere in the Coachella Valley, book our professional refrigerator repair service online or call our local dispatch team at (760) 537-6751.

Transparent Invoice Breakdown

ETS Appliance Repair provides upfront, flat-rate pricing before we touch a single screw:

Service Item / ComponentDescriptionInvestment
Technician Diagnostic, Multimeter Valve Test & Leak InspectionValve coil test, thermal fuse check & leak origin tracing (waived upon repair approval)$0.00
Genuine OEM Thermador Complete Ice Maker AssemblyFactory-certified ice maker module and mold head (Part #11036056)$465.00
Certified Refrigeration LaborSteam ice removal, multi-pin plug transfer, OEM module installation & harvest calibration$265.00
Total Repair InvestmentComplete Leak Resolution & 90-Day Parts and Labor Warranty$730.00

Repair completed on-site in Palm Desert, CA (92260) in approximately 60 minutes. Backed by our standard 90-day parts and labor warranty under CA BHGS License #A51622.

Related Service Areas & Specialized Repairs:
Same-Day San Diego Service

Need Technician Assistance Today?

$99.95 Technician Diagnostic Visit • 100% Waived With Completed Repair.

Call (619) 332-2028
Google Customer Reviews

Real Google Reviews From Satisfied Clients

Verified customer ratings from homeowners and businesses across San Diego County & Coachella Valley.

4.7

Google Rating (28 Verified Reviews)

WK

W K

a month ago

“Henry has been great....couldn't have been more knowledgeable and did a great job.....hope if I need help again he is available”

Coronado / San Diego, CA
Appliance Diagnostic & Repair
BL

Brent Lagace

a week ago

“Great service! Excellent staff! Thank you!”

San Diego / Coronado, CA
Appliance Diagnostic & Repair
CR

Chris Rea

a month ago

“Henry arrived and quickly got the dryer opened up and vacuumed, checked all sensors and greased rollers. Very fast, very thorough! Great job!”

San Diego / Coronado, CA
Dryer Repair & Service
Reviews automatically synchronized via official Google Places API
Have you used our service? Leave a review on Google →
Call Now